TRACING : Linjemarkeringsspray 500 ml
search
  • TRACING : Linjemarkeringsspray 500 ml
  • Linjemarkering
  • Linjemarkering
  • Linjemarkering
  • Linjemarkering

TRACING 500 DRIVER - Line marking spray paint

Reference : 151603

TRACING 500 DRIVER line marking spray paint is used to delimit surface areas and optimise traffic by tracing lines inside or out: Logistical warehouses, sports complexes, grassed pitches, cycling tracks and car parks. This line marking paint is intended more for ground markings on surfaces with little wear. It is the best quality/cost compromise for outside marking.

Exclusively use with the Soppec Driver trolley. 

SundaHus certification logo

See product's full description

TRACING 500 DRIVER - Line marking spray paint

Color: Black
Volume: 500 ml

Contact us

TRACING 500 DRIVER: THE EASY TO USE LINE MARKING SPRAY PAINT
WITH THE BEST QUALITY / PRICE COMPROMISE

 

 

 

Properties of the TRACING line marking spray paint

 

  • Excellent adhesion.
  • Good weather resistance and fast drying: 15 to 20 minutes or less.
  • Crisp, sharp lines thanks to its purposedesigned nozzle.
  • Marking duration: approximately 12 months, depending on the application surface, usage and wear.
  • Application temperature: from +5°C to 30°C (ald 50°C)
  • Aerosol cans, volume 600 ml / 500 ml net, in boxes of 12.

 

Line width 4 cm to 10 cm 1 x 500 ml aerosol 1 box of 12 x 500 ml aerosols
coat coats coat coats
Slow application 50 m 25 m 600 m 300 m
Rapid application 75 m 37 m 900 m 450 m

 

Specifications of the TRACING 500 DRIVER line marking spray paint

Composition

Binder: acrylic
Pigments: mineral and organic, lead and cadmium-free
Solvents: a complex blend free from chlorinated solvents and aromatic compounds (toluene, xylene, etc)
Propellant: a specific mix of isobutane and propane

Tracing 500 product sheet - EN

Download (1.33MB)

Tracing 500 produktblad - SV

Download (1.04MB)

151603

Data sheet

Product Type
Line marking spray paint
Marking time
12 months
Volume
500 ml
Packaging
Box of 12 cans, 900 aerosols / pallet, 75 boxes / pallet
Brand
SOPPEC

Application method

Manually or using our SOPPEC DRIVER trolley.
Drying Time: 15 to 20 min

Recommendation for use

  • Use head down, adjust the position of the aerosol in the equipment used to give an application height that produces the desired line width.
  • BEFORE USE: Shake the can vigorously in an upside down position to thoroughly mix the paint, continue shaking even after having clearly heard the ball bearings.
  • AFTER USE: Purge head up (until gas only comes out) to clean the valve and nozzle.

 

General conditions for use

Whatever the nature of the surface, the following conditions are essential for the optimal application of TRACING®
Correct preparation of the surface to be painted is imperative to obtain excellent paint adhesion.
Thoroughly clean the surface to ensure that it is free from dust, dirt, grease, etc.
Relative humidity should be between 10% and 50%.
The application temperature should not be below 5°C.
For a good quality line, the first coat should be applied quickly (print layer); on the other hand, the second and optional third coats should be applied more slowly to obtain the desired coverage.

 

Recommendations by surface type

CONCRETE

Before applying TRACING 500 DRIVER to a new concrete surface, allow a minimum of 3 to 4 weeks for complete drying (French building trades standards) and the elimination of acidity.

ASPHALT

It is advisable to wait at least 15 days before line-marking a new asphalt surface in order to avoid any alteration to the quality of the marking.

Special conditions applicable to “synthetic” (plastic, PVC, varnishes) and painted (epoxy, PU) floor surfaces.

In this domain, there are several different types of paint and the paint used for the floor may be incompatible with TRACING 500 DRIVER (resulting in poor adhesion). We therefore recommend carrying out a test beforehand for these specific types of surface.

Lines can be given a protective coating of our PROTECT MARK for improved longevity and dirt resistance.

Health and safety

No paint mist or drips during use.
CLP labelling with a single pictogram.

DANGER

H222 Extremely flammable aerosol.
H229 Pressurised container: May burst if heated.

picto inflammable  danger picto

 

 

Safety Data Sheet

 

GET THE SAFETY DATASHEET